Home > Products > Liquid Solution > Alternative Oil Filter Element > Other Brand > PI8405PRG60 Replace Mahle Oil Filter Element

PI8405PRG60 Replace Mahle Oil Filter Element

Part number
PI8405PRG60
End caps
Carbon steel
Filter material
Stainless steel mesh
Filtration rate
Customized
Support core
Carbon steel perforated plate
Working temperature
-20~+110℃
Origin
Henan,China
Share:
Products Description
Specification
Features

Products Description

The PI8405PRG60 replacement hydraulic oil filter is a high-performance stainless steel wire mesh filter cartridge designed to be fully compatible with the original Mahle PI8405DRG60 series filtration systems. This replaceable filter element is the essential consumable component within PI8400 series filter modules and compatible industrial filtration assemblies, widely used in hydraulic power units, lubrication systems, steel mills, power plants, and mobile machinery.

Within hydraulic and lubrication systems, the PI8405PRG60 replacement filter element is typically installed in pressure line filters, suction filters, or continuous oil purification circuits where reliable removal of solid contaminants is critical to system reliability and component longevity. As a surface filter with stainless steel wire mesh media, the element captures solid particles larger than the rated micron size on the mesh surface.

Specification

This is the specification of the standard PI8405PRG60 replace oil filter element. If you need other part number, please contact us.

Type Replace Oil Filter Element
Part number PI8405PRG60
End caps Carbon steel
Filter material Stainless steel mesh
Filtration rate Customized
Support core Outside to Inside
Origin Henan, China
Package Neutral carton package

 

Features

High-Efficiency Depth Filtration: Features advanced pleated media designed for excellent contaminant capture and retention, effectively maintaining required fluid cleanliness levels to protect sensitive components.
Durable & Reliable Construction: Built with a robust inner support core and securely bonded end caps to withstand pressure differentials and prevent media migration, ensuring stable performance throughout its service life.
Essential System Protection: Safeguards sensitive hydraulic components from abrasive wear, helping to maintain operational efficiency, reduce repair frequency, and maximize equipment uptime.
Cost-Effective Maintenance Solution: Provides a high-value, reliable alternative for preventive maintenance programs, contributing to a lower total cost of ownership.
Didn't find your industry solution? Consult our technical experts immediately.

Manufacturer of Replace Oil Filter Element

Huahang Filter is a professional filtration manufacturer with over a decade of experience in designing and producing high-quality replacement filter cartridges. Since our founding in 2009, we have focused on delivering filtration solutions that balance performance, durability, and cost-effectiveness.

Product Profile of Huahang Filter

Huahang serves a global clientele across vital sectors. Our portfolio spans:

  • Sintered Filters: For high-temperature gas filtration, polymer melt filtration, and critical fluid protection.
  • Replacement Filter Elements: Precision equivalents for major OEM brands (including Parker, Hydac, Pal and others), ensuring system compatibility without compromise.
  • Oil Filter Cartridges: A full spectrum of depth, particulate, and coalescing filters for lubrication, hydraulic, and fuel systems.

In addition to standard models, Huahang filter can also provide customized service according to customer needs, including dimensions, materials, end caps, and filter housings. Please contact us for specific information.

Applications

  • Steel Mills and Heavy Metal Processing : Filters hydraulic and lubricating oil in rolling mills, continuous casting lines, blast furnace controls, and heavy plate processing equipment. The reusable design reduces long-term consumables costs in these high-wear environments.
  • Power Generation : Protects turbine bearing lubrication systems, coal mill lubrication circuits, generator cooling oil systems, and hydraulic control systems in thermal, hydroelectric, and wind power facilities.
  • Industrial Hydraulic Systems : Removes solid particles and gelatinous contaminants from hydraulic fluid in manufacturing equipment, plastic injection molding machines, hydraulic presses, and machine tools.
  • Petrochemical and Chemical Processing : Filters process fluids, chemical streams, and lubrication circuits in refineries, chemical plants, and gas processing facilities where stainless steel provides superior chemical resistance.
  • Marine and Shipbuilding : Protects hydraulic steering systems, deck machinery controls, thruster hydraulics, and engine lubrication circuits operating in saltwater environments.

FAQ

Q1: What is the flow direction through this element?
A: The flow direction is outside-in. Hydraulic fluid enters from the outside of the element and passes through the filter media to the inner core, capturing contaminants on the outer layers.

Q2: Can this PI8405PRG60 filter element be cleaned and reused?
A: No. This filter’s end caps are not stainless steel material. They are made of carbon steel. This material cannot clean. Only whole stainless steel material filter elements like sintered filter and candle oil filter can be cleaned.

Q3: How do I know when to replace this filter element?
A: Replace when the differential pressure indicator signals, when pressure drop reaches the manufacturer’s recommended maximum, or during scheduled maintenance intervals (typically every 2000-4000 operating hours).

Q4: What industries commonly use this PI4108PS25 filter element?
A: This element is widely used in metallurgy (rolling mills, continuous casting), power generation (turbine lubrication, speed control systems), injection molding, heavy industrial machinery, petrochemical processing, marine applications, and various industrial hydraulic systems requiring high-pressure filtration.

Custom Service

At Huahang Filter, we offer robust customization services to meet your specific filtration requirements.

  • Custom Filtration Ratings: Available from 1μm to 25μm to match your exact particle removal requirements.

  • Custom Seal Materials: NBR, Viton, EPDM, or PTFE-encapsulated options available.

  • Custom End Caps: Alternative materials or configurations to fit unique housings.

  • Special Media Options: Wire mesh for cleanable applications or enhanced cellulose blends.

  • Custom Packaging: Bulk packaging or individual boxes with branding and instructions.

Contact Huahang Filter today to discuss your MOOG B645662V replacement filter element requirements and request a quote!

Related Products

Related Cases

Xinxiang City Huahang Filter Co., Ltd is professional in the production of Hydraulic Filter, Air Filter and Pipe Filter.Product series range from Oil Filter, Air Filter, Water Filter, Polymer Filter,Candle Filter Element, Stainless Steel Filter to filter Coalescer and Separator.

FAQ

How do I cross-reference my existing OEM part number to a Huahang element?

Send the OEM number plus one physical measurement. A part number alone is not enough to ship against.


* What we match on — Outside diameter, inside diameter, overall height, media grade, micron rating, end-cap and seal layout, bypass setting, collapse rating and flow direction.


* When the number is ambiguous — Superseded numbers, numbers shared across several machine builds, or an element that has clearly been substituted before. In those cases a photo of the housing nameplate and a caliper reading of the old element settle it.


* Why we insist — The most common return is not a wrong size. It is an element that fits the bore but seals on the wrong face.

What collapse or burst pressure can your elements take, and how does flow direction affect it?

Collapse rating comes from the core, not the media — and it only holds in service if two conditions are met.


* Typical ranges — A light return-line element with a perforated core around 10–25 bar; a pressure-line element with a heavy spiral core 100 bar and above; high-collapse designs higher still.


* Condition 1 — flow direction — Return elements are normally outside-in. Run one backwards and the pleat pack goes into tension, folds, and bypasses.


* Condition 2 — bypass setting — The housing’s bypass valve must crack below the element’s collapse rating. Otherwise a cold start or a neglected change-out crushes the element before the valve ever opens.

Can your elements handle fire-resistant fluids such as phosphate ester and EHC systems?

Yes, but the build changes, and this is exactly where a generic replacement fails.


* Seals — Move to FKM or PTFE. NBR swells and softens in phosphate ester.


* Media and bonds — Binder, pleat-seam adhesive and end-cap adhesive all have to resist ester attack; some phenolic resin systems do not.


* Water-based fluids (HFA, HFC) — A different problem again — free water, biological growth, and media that must not delaminate when wet.


* Expect a different ΔP — These fluids run at higher viscosity and lower lubricity than mineral oil, so the same element reads differently on the gauge.

What is the difference between an oil separator element and an oil mist separator?

Same job at different pressures: one works inside a compressor separator tank, the other on a breather or vacuum pump.


* Oil separator element — Removes oil aerosol from compressed air and returns the collected oil to the sump. Rated in mg/m³ carryover, typically a few mg/m³ for a healthy element.


* Oil mist separator — Comparable duty at near-atmospheric pressure, but sized on flow and oil type rather than on pressure.


* Saturation signals, common to both — Carryover climbing, oil consumption rising with no visible leak, ΔP trending up, and an element that comes out dark and varnished instead of evenly coated.

Sintered mesh, sintered powder or pleated stainless steel — how do I choose between them?

Choose on duty, not on price. The three constructions also fail in different ways.


* Sintered mesh : 2 to 5 diffusion-bonded wire layers — High strength, genuinely backflushable, cleanable surface, absolute ratings typically 3–100 µm. Best for catalyst recovery, amine and water service, and anything cleaned in place.


* Sintered powder : A true depth filter: narrow pore distribution, finer ratings (0.5–1 µm with titanium), more dirt capacity per unit area, better resistance to compressive load. The default for polymer melt, high-pressure gas and food or pharmaceutical duty where no fibre release is allowed.


* Pleated stainless : Woven wire cloth in a pleat pack — large area and low ΔP at high flow for coarse duty, and the lowest cost per square metre of area.

How do you ensure the quality and performance of the filter element?

Quality is our lifeline. We insist on:


Strict material selection: Use high-quality raw materials that meet industry standards.


Advanced technology: Use automated or precision-controlled production processes.


Multiple quality inspections: Implement full-process quality inspections from raw material storage to finished product delivery (including size, sealing, filtration efficiency, integrity testing, etc.).


Performance testing: Key products will undergo actual working condition simulation testing.


Compliance with standards: Our production and products comply with [e.g.: ISO 9001].


Customized verification: For customized filter elements, we will confirm key performance indicators with customers and provide test reports (if necessary).

Can metal cartridges be cleaned and reused, and how many cycles should I expect?

Yes . Reusability is usually the whole economic case, and it comes with two hard rules.


* Methods — Reverse-flow backflush at 1.5–2× service rate, ultrasonic cleaning in mild alkaline detergent, caustic or acid CIP, and calcination or steam for carbon and polymer residues.


* Never brush or scrape — That smears the pore structure and drives contamination deeper instead of out.


* Stay inside the chloride limit — 304 will pit at the weld in chloride-bearing water long before the media fails.


* Track the clean ΔP — Once it sits 30–50% above the original baseline, the pore structure is degrading rather than fouling — the cartridge is finished.

What is the difference between nominal and absolute micron ratings on metal media?

The two words are not interchangeable, and the gap between them is where process upsets come from.


- Nominal — Means 90–95% of particles above the stated size are retained, usually with no defined test method behind the claim.


- Absolute — Means 99.9% or better, verified by a defined method — bubble point to ISO 4003, glass-bead challenge, or a recognised particulate challenge.


- Ask which method — Metal ratings are normally derived from bubble-point pore size, so the method is the number.


- Why it matters — A mesh sold as 10 µm nominal will comfortably pass 25 µm particles. Irrelevant for a coarse strainer; fatal upstream of a spin pack or a membrane.

How do I specify a metal cartridge for polymer melt filtration?

Two numbers decide whether the cartridge survives: start-up ΔP, and collapse rating against the screen changer’s maximum.


* Process data — Polymer type (PET, PP, PA6, PE), melt temperature, viscosity at that temperature, throughput in kg/h, allowable pressure build-up.


* Hardware — Screen changer, spin pack or candle housing, with its pressure rating.


* Design on start-up, not steady state — Cold polymer can produce five to ten times the service differential pressure.


* No fibre release — Sintered powder or sintered mesh, not woven cloth, downstream of an extruder.

What do you need for a custom end connection, thread or flange?

Flange standards cause more rework than any other single item on a custom order.


* Dimensions : OD, ID, overall length, thread or flange specification and bolt circle. A drawing, or a photo with a caliper in frame, is enough.


* Connection and seal : M30×1, M36×2, BSP or NPT thread, ANSI or DIN flange, quick connector, bayonet — plus seal type and material.


* Duty : Media and rating, flow, allowable ΔP, temperature, pressure, quantity.

Which filter media should I use for my dust — polyester, anti-static, fiberglass, paper or non-woven?

Match the media to the dust chemistry and to how the collector cleans. Price is the last criterion.


- Polyester needle felt — to about 130 °C — General dry dust. The default choice, and the right starting point for most collectors.


- PTFE-laminated polyester — to about 130 °C — Fine or sticky fume, where dust must not key into the depth of the felt.


- Anti-static polyester, carbon or stainless fibre — to about 130 °C — Combustible dust, and any stream where charge build-up makes the cartridge hold dust it should have released.


- Fiberglass — to about 250 °C — High temperature, and any duty requiring H13 or H14 efficiency.


- Paper or cellulose — Coarse pre-filtration where cost dominates.


- Non-woven synthetic blends — Abrasive or moisture-laden streams.

Does a higher pleat count always mean better performance?

More pleats means more area — until the pleats crowd and cleaning can no longer reach the pleat root.


* What you gain — Lower face velocity, and therefore lower differential pressure at a given flow.


* What you lose — The gaps close under load, the cartridge blinds from the inside out, and the extra area is wasted.


* The metric that matters — Pleat pitch against dust loading: fine sticky dust wants wide spacing, free-flowing granular dust tolerates tight packing.


* Also check — Pleat depth against cage inside diameter. Deep pleats in a small cartridge fold over and create a dead zone that never cleans.

Why do my cartridges fail before their rated life, and how can I extend it?

Four modes account for most premature change-outs, and the fixes sit upstream of the cartridge.


* Media burst or abrasion — High inlet velocity, a missing deflector, or pulse pressure over about 6 bar at the venturi.


* Cage collapse — Differential pressure above rating, or water ingress.


* Adhesive or gasket failure — Temperature past the glue’s limit, or solvent attack.


* Rust-through — Galvanised cages in condensing streams.

What is the difference between a coalescer filter and a separator filter?

They are two distinct technologies often used together to remove liquids from a gas or liquid stream. The key difference is their core function:

* A Coalescer Filter merges tiny, invisible liquid droplets into large, heavy ones.

* A Separator Filter catches and drains those large droplets from the flow.

How They Work:

* Coalescer: The stream passes through a special media (like fine fibers). Microscopic aerosol droplets collide and merge (coalesce) into drops large enough to drain. It solves the problem of suspended mist.

* Separator: The flow then enters a chamber with baffles or vanes. The now-large droplets hit the surfaces, fall out by gravity, and collect in a sump. It provides the final, clean separation.

When do I need fiberglass or stainless instead of polyester, and how do I handle sparks?

Above roughly 130 °C continuous, polyester is out — and the gasket and cage need checking at the same time.

* Next step up — Fiberglass holds to about 260 °C; stainless or ceramic options go further.

* The weak link changes — Often the media survives and the glue line fails first, so the temperature rating must cover the whole assembly.

* Sparks — Welding, grinding, biomass boilers, foundry: a spark arrestor or pre-settling chamber upstream is mandatory. Fiberglass resists heat, not molten metal impingement.

* Condensing streams — Acid dew point corrodes cages faster than it destroys media, and a rusted cage collapses into the fan.
373-5471699
info@huahangfilter.com
+86 16690927259

    X