Home > Products > Liquid Solution > Alternative Oil Filter Element > LEEMIN Filter > SWCQ-A25×80 Replace Leemin Hydraulic Oil Filter

SWCQ-A25×80 Replace Leemin Hydraulic Oil Filter

Product type
Replace Hydraulic Oil Filter Element
Part number
SWCQ-A25×80
Filter layer
Fiberglass
End caps
Carbon steel
Filtration rate
Customized
Working temperature
-30~+110℃
Origin
Henan,China
Package
Neutral carton package
Share:
Products Description
Specification
Features

Products Description

The SWCQ-A25×80 hydraulic oil filter element is a high-performance replacement filter cartridge designed specifically for Leemin dual-tank lubricating oil filtration systems. This filter element is the core consumable component used within SWCQ series duplex filters, commonly found in thin oil lubrication systems for industrial machinery and power generation equipment.

The SWCQ-A25×80 hydraulic filter cartridge is installed at the oil pump outlet or upstream of the cooler within the lubrication system, where it continuously removes mechanical impurities, metal wear debris, rubber particles, and other contaminants from the hydraulic fluid and lubricating oil. By maintaining the cleanliness of the working medium, this replacement hydraulic oil filter cartridge helps protect downstream equipment such as pumps, valves, bearings, and hydraulic actuators from premature wear and failure.

Specifications

SWCQ-A25×80 replace Leemin hydraulic oil filter elements are manufactured and tested according to international standards to ensure quality and reliability.

Type Replace Hydraulic Oil Filter Element
Part number SWCQ-A25×80
Filter layer Fiberglass
Working pressure 21~210 bar
Filtration rate Customized
Working temperature -30~+110℃
Nominal flow rate 1.0 Mpa
Maximum differential pressure 21 Mpa

Features

Direct Replacement: Manufactured to exact specifications for a perfect fit with Leemin and other major brand return line filter housings
Advanced Filtration Media Composition – The SWCQ-A25×80 hydraulic filter cartridge utilizes multi-layer filtration media. The fiberglass media features a high-strength fiber structure with high porosity, delivering both high filtration accuracy and superior dirt-holding capacity.
Robust Construction: Features heavy-duty perforated steel inner support tubes and durable end caps (galvanized steel or high-strength plastic), providing high collapse pressure resistance and ensuring structural integrity under variable flow rates
Optimized Flow & Long Service Life: High dirt-holding capacity, large filtration area, and low initial pressure drop contribute to longer service life (up to 2000 hours ) and reduced operating costs
Didn't find your industry solution? Consult our technical experts immediately.

Optional Part Number

There are part of the models related to the SWCQ-A25×80 Replace Leemin Oil Filter Element. Feel free to contact us for a detailed quote.

SFX-1300×10 FBX-400×20 TZX2-40×50W SFBX-25×30 SFBX-40×1 SFBX-40×3 SFBX-40×5 SFBX-40×10
SFBX-40×20 SFBX-40×30 SFBX-63×1 SFBX-63×3 SFBX-63×5 SFBX-63×10 SFBX-63×20 SFBX-63×30
SFBX-100×1 SFBX-100×3 SFBX-100×5 SFBX-100×10 SFBX-100×20 SFBX-100×30 SFBX-160×1 SFBX-160×3
SFBX-160×5 SFBX-160×10 SFBX-160×20 SFBX-160×30 SFBX-250×1 SFBX-250×3 SFBX-250×5 SFBX-250×10
SFBX-250×20 SFBX-250×30 SFBX-400×1 SFBX-400×3 SFBX-400×5 SFBX-400×10 SFBX-400×20 SFBX-400×30
SFBX-630×1 SFBX-630×3 SFBX-630×5 SFBX-630×10 SFBX-630×20 SFBX-630×30 SFBX-800×1 SFBX-800×3

Customization Available

At Huahang Filter, we recognize that standard replacement parts are not always the perfect fit. We offer a robust Custom Service to tailor the filters to your specific needs . If you require a variation from the standard model, we can engineer it.

  • Custom Dimensions: Need a different length, outer diameter, or inner diameter to fit a non-standard housing? We can modify the core structure to meet your space constraints .

  • Custom Filtration Ratings: Choose from a range of filtration efficiencies from 1μm to 100μm to achieve your desired cleanliness levels .

  • Custom Packaging: From bulk packaging to individual retail boxes, or specific labeling requirements for OEM projects, we can customize the packaging to suit your inventory and branding needs .

  • Custom End Caps: We can manufacture alternative end cap configurations or materials (stainless steel, aluminum, reinforced nylon) to ensure the element seals correctly in various housing designs .

  • Custom Filter Media: Choose from a variety of media types, including microfiber glass, stainless steel wire mesh, stainless steel sintered mesh, cellulose, or synthetic blends, to achieve different filtration efficiencies, dirt-holding capacities, or chemical compatibilities .

  • Special Seal Materials: In addition to standard NBR (Nitrile), we offer seals in Viton (FKM) , EPDM, or Silicone to handle aggressive fluids or extreme temperatures

Contact Huahang Filter today to discuss your specific requirements and request a quote!

Replacement Oil Filter Manufacturer

Xinxiang City Huahang Filter Co., Ltd. is a professional ISO 9001 certified manufacturer specializing in the design, production, and sale of hydraulic filters, air filters, water filter cartridges, and liquid filtration systems. Established in 2003, the company operates from a modern production facility in Xinxiang City, Henan Province—one of China’s most prominent filtration industry clusters.

Our comprehensive product portfolio spans hydraulic oil filter elements, air intake filters, water purification cartridges, polymer filters, stainless steel filter elements, coalescer cartridges, separator cartridges, and complete filter housings in tubular, plate-type, pleated, and wrap-type configurations. Huahang Filter also supplies replacement elements compatible with major international brands including Leemin, PAL, HYDAC, ARGO, PARKER, MAHLE, and so on.

Why Choose Huahang Filter

➤ ISO 9001 Certified Quality Management System: Huahang operates under a certified quality management system, with rigorous raw material inspection, in-process quality control, and 100% finished product testing before shipment.

➤ 20+ Years of Filtration Manufacturing Expertise: With over two decades of continuous operation in the filtration industry, Huahang has developed deep technical knowledge across hydraulic, lubrication, air, and liquid filtration applications.

➤ True Manufacturer Direct Pricing: As a factory-direct manufacturer rather than a trading intermediary, Huahang offers the SWCQ-A25×80 hydraulic filter replacement element at competitive factory-direct prices, eliminating unnecessary markups while maintaining exceptional quality standards.

➤ Dedicated Technical Support: Our engineering and application support team is available to assist with filter selection, cross-reference verification, installation guidance, and troubleshooting for the SWCQ-A25×80 hydraulic oil replacement element or any other filtration challenge you may encounter.

FAQ

Q: How is this different from the OEM Leemin filter?
A: Huahang’s element is manufactured to meet or exceed the original Leemin specifications for filtration efficiency, dirt-holding capacity, pressure drop, and dimensional accuracy. The difference is price and availability. Huahang’s factory-direct pricing is significantly lower, and lead times are often shorter.

Q: What filtration efficiency can I expect?
A: The glass fiber media provides βₓ ≥ 100 for the specified micron rating, which means at least 99% of particles at or above the rated size are captured in a single pass through the element. Multi-pass testing per ISO 16889 confirms performance.

Q: Do you ship internationally?
A: Yes. Huahang ships worldwide via air freight, sea freight, and express couriers (DHL, FedEx, UPS). Delivery times vary by destination and quantity.

Q: How do I install the element correctly?
A: Installation steps: Shut down the hydraulic system and relieve all pressure. Remove the filter housing cover. Carefully remove the old element. Clean the housing interior. Install the new element with new seals if included. Reinstall the housing cover and tighten to the torque specified in your equipment manual. Restart the system and check for leaks.

Related Products

Related Cases

Xinxiang City Huahang Filter Co., Ltd is professional in the production of Hydraulic Filter, Air Filter and Pipe Filter.Product series range from Oil Filter, Air Filter, Water Filter, Polymer Filter,Candle Filter Element, Stainless Steel Filter to filter Coalescer and Separator.

FAQ

How do I cross-reference my existing OEM part number to a Huahang element?

Send the OEM number plus one physical measurement. A part number alone is not enough to ship against.


* What we match on — Outside diameter, inside diameter, overall height, media grade, micron rating, end-cap and seal layout, bypass setting, collapse rating and flow direction.


* When the number is ambiguous — Superseded numbers, numbers shared across several machine builds, or an element that has clearly been substituted before. In those cases a photo of the housing nameplate and a caliper reading of the old element settle it.


* Why we insist — The most common return is not a wrong size. It is an element that fits the bore but seals on the wrong face.

What collapse or burst pressure can your elements take, and how does flow direction affect it?

Collapse rating comes from the core, not the media — and it only holds in service if two conditions are met.


* Typical ranges — A light return-line element with a perforated core around 10–25 bar; a pressure-line element with a heavy spiral core 100 bar and above; high-collapse designs higher still.


* Condition 1 — flow direction — Return elements are normally outside-in. Run one backwards and the pleat pack goes into tension, folds, and bypasses.


* Condition 2 — bypass setting — The housing’s bypass valve must crack below the element’s collapse rating. Otherwise a cold start or a neglected change-out crushes the element before the valve ever opens.

Can your elements handle fire-resistant fluids such as phosphate ester and EHC systems?

Yes, but the build changes, and this is exactly where a generic replacement fails.


* Seals — Move to FKM or PTFE. NBR swells and softens in phosphate ester.


* Media and bonds — Binder, pleat-seam adhesive and end-cap adhesive all have to resist ester attack; some phenolic resin systems do not.


* Water-based fluids (HFA, HFC) — A different problem again — free water, biological growth, and media that must not delaminate when wet.


* Expect a different ΔP — These fluids run at higher viscosity and lower lubricity than mineral oil, so the same element reads differently on the gauge.

What is the difference between an oil separator element and an oil mist separator?

Same job at different pressures: one works inside a compressor separator tank, the other on a breather or vacuum pump.


* Oil separator element — Removes oil aerosol from compressed air and returns the collected oil to the sump. Rated in mg/m³ carryover, typically a few mg/m³ for a healthy element.


* Oil mist separator — Comparable duty at near-atmospheric pressure, but sized on flow and oil type rather than on pressure.


* Saturation signals, common to both — Carryover climbing, oil consumption rising with no visible leak, ΔP trending up, and an element that comes out dark and varnished instead of evenly coated.

Sintered mesh, sintered powder or pleated stainless steel — how do I choose between them?

Choose on duty, not on price. The three constructions also fail in different ways.


* Sintered mesh : 2 to 5 diffusion-bonded wire layers — High strength, genuinely backflushable, cleanable surface, absolute ratings typically 3–100 µm. Best for catalyst recovery, amine and water service, and anything cleaned in place.


* Sintered powder : A true depth filter: narrow pore distribution, finer ratings (0.5–1 µm with titanium), more dirt capacity per unit area, better resistance to compressive load. The default for polymer melt, high-pressure gas and food or pharmaceutical duty where no fibre release is allowed.


* Pleated stainless : Woven wire cloth in a pleat pack — large area and low ΔP at high flow for coarse duty, and the lowest cost per square metre of area.

How do you ensure the quality and performance of the filter element?

Quality is our lifeline. We insist on:


Strict material selection: Use high-quality raw materials that meet industry standards.


Advanced technology: Use automated or precision-controlled production processes.


Multiple quality inspections: Implement full-process quality inspections from raw material storage to finished product delivery (including size, sealing, filtration efficiency, integrity testing, etc.).


Performance testing: Key products will undergo actual working condition simulation testing.


Compliance with standards: Our production and products comply with [e.g.: ISO 9001].


Customized verification: For customized filter elements, we will confirm key performance indicators with customers and provide test reports (if necessary).

Can metal cartridges be cleaned and reused, and how many cycles should I expect?

Yes . Reusability is usually the whole economic case, and it comes with two hard rules.


* Methods — Reverse-flow backflush at 1.5–2× service rate, ultrasonic cleaning in mild alkaline detergent, caustic or acid CIP, and calcination or steam for carbon and polymer residues.


* Never brush or scrape — That smears the pore structure and drives contamination deeper instead of out.


* Stay inside the chloride limit — 304 will pit at the weld in chloride-bearing water long before the media fails.


* Track the clean ΔP — Once it sits 30–50% above the original baseline, the pore structure is degrading rather than fouling — the cartridge is finished.

What is the difference between nominal and absolute micron ratings on metal media?

The two words are not interchangeable, and the gap between them is where process upsets come from.


- Nominal — Means 90–95% of particles above the stated size are retained, usually with no defined test method behind the claim.


- Absolute — Means 99.9% or better, verified by a defined method — bubble point to ISO 4003, glass-bead challenge, or a recognised particulate challenge.


- Ask which method — Metal ratings are normally derived from bubble-point pore size, so the method is the number.


- Why it matters — A mesh sold as 10 µm nominal will comfortably pass 25 µm particles. Irrelevant for a coarse strainer; fatal upstream of a spin pack or a membrane.

How do I specify a metal cartridge for polymer melt filtration?

Two numbers decide whether the cartridge survives: start-up ΔP, and collapse rating against the screen changer’s maximum.


* Process data — Polymer type (PET, PP, PA6, PE), melt temperature, viscosity at that temperature, throughput in kg/h, allowable pressure build-up.


* Hardware — Screen changer, spin pack or candle housing, with its pressure rating.


* Design on start-up, not steady state — Cold polymer can produce five to ten times the service differential pressure.


* No fibre release — Sintered powder or sintered mesh, not woven cloth, downstream of an extruder.

What do you need for a custom end connection, thread or flange?

Flange standards cause more rework than any other single item on a custom order.


* Dimensions : OD, ID, overall length, thread or flange specification and bolt circle. A drawing, or a photo with a caliper in frame, is enough.


* Connection and seal : M30×1, M36×2, BSP or NPT thread, ANSI or DIN flange, quick connector, bayonet — plus seal type and material.


* Duty : Media and rating, flow, allowable ΔP, temperature, pressure, quantity.

Which filter media should I use for my dust — polyester, anti-static, fiberglass, paper or non-woven?

Match the media to the dust chemistry and to how the collector cleans. Price is the last criterion.


- Polyester needle felt — to about 130 °C — General dry dust. The default choice, and the right starting point for most collectors.


- PTFE-laminated polyester — to about 130 °C — Fine or sticky fume, where dust must not key into the depth of the felt.


- Anti-static polyester, carbon or stainless fibre — to about 130 °C — Combustible dust, and any stream where charge build-up makes the cartridge hold dust it should have released.


- Fiberglass — to about 250 °C — High temperature, and any duty requiring H13 or H14 efficiency.


- Paper or cellulose — Coarse pre-filtration where cost dominates.


- Non-woven synthetic blends — Abrasive or moisture-laden streams.

Does a higher pleat count always mean better performance?

More pleats means more area — until the pleats crowd and cleaning can no longer reach the pleat root.


* What you gain — Lower face velocity, and therefore lower differential pressure at a given flow.


* What you lose — The gaps close under load, the cartridge blinds from the inside out, and the extra area is wasted.


* The metric that matters — Pleat pitch against dust loading: fine sticky dust wants wide spacing, free-flowing granular dust tolerates tight packing.


* Also check — Pleat depth against cage inside diameter. Deep pleats in a small cartridge fold over and create a dead zone that never cleans.

Why do my cartridges fail before their rated life, and how can I extend it?

Four modes account for most premature change-outs, and the fixes sit upstream of the cartridge.


* Media burst or abrasion — High inlet velocity, a missing deflector, or pulse pressure over about 6 bar at the venturi.


* Cage collapse — Differential pressure above rating, or water ingress.


* Adhesive or gasket failure — Temperature past the glue’s limit, or solvent attack.


* Rust-through — Galvanised cages in condensing streams.

What is the difference between a coalescer filter and a separator filter?

They are two distinct technologies often used together to remove liquids from a gas or liquid stream. The key difference is their core function:

* A Coalescer Filter merges tiny, invisible liquid droplets into large, heavy ones.

* A Separator Filter catches and drains those large droplets from the flow.

How They Work:

* Coalescer: The stream passes through a special media (like fine fibers). Microscopic aerosol droplets collide and merge (coalesce) into drops large enough to drain. It solves the problem of suspended mist.

* Separator: The flow then enters a chamber with baffles or vanes. The now-large droplets hit the surfaces, fall out by gravity, and collect in a sump. It provides the final, clean separation.

When do I need fiberglass or stainless instead of polyester, and how do I handle sparks?

Above roughly 130 °C continuous, polyester is out — and the gasket and cage need checking at the same time.

* Next step up — Fiberglass holds to about 260 °C; stainless or ceramic options go further.

* The weak link changes — Often the media survives and the glue line fails first, so the temperature rating must cover the whole assembly.

* Sparks — Welding, grinding, biomass boilers, foundry: a spark arrestor or pre-settling chamber upstream is mandatory. Fiberglass resists heat, not molten metal impingement.

* Condensing streams — Acid dew point corrodes cages faster than it destroys media, and a rusted cage collapses into the fan.
373-5471699
info@huahangfilter.com
+86 16690927259

    X